Settling in Takes Time
The delay in posting has been caused by a number of things,
Microsoft updates which cause the mouse to sonar deeper than what you
click on, multiple clicking in general its been a sore point as it
interferes with so much.
Long days which by the time I check emails etc I am tuckered out so have resorted to doing only what is needed.
A few sick days nothing major change to weather, sinus and hay fever slowing everything down. Ah well press on.
The weather of late has been fantastic even the early morning temps
of down to 0C and by 10am its 17C+ its not effecting me as it would have
down south. in fact arthritis has eased a whole deal for both of us.
So there is lots to catch up with firstly the Burl which at the
moment has taken a back seat. it sat out for days being flattened using a
garden pot, potting mix as weight, turned every other day. Finally I
could run the electric hand planer over the high/thick spots which took
out some tension areas. A few more days before taking it in and clamping
it to an MDF board and hand planing it as flat as possible both sides.
It took a few days, its been stored until such time as I can set up the
plywood base cut it to shape this will only be to give support and
somewhere to secure the frame work of the corner table.
Prior leaving Sydney I had secured some original Myford accessories
through a forum sale the gent was very kind in holding off until we had
moved to post them as well as I didn’t have to pay till I had them in my
hot little hands.
I scored a Myford Fixed steady rest, Myford Angle Plate, set of
original Myford ML7 manuals and booklets. set of Myford Carbide tooling
All in excellent condition some unused, posted from South Australia the gent who owned them was retiring had sold off the lathe.
Installed a metal hose tidy for Sue. I screwed it onto the wall using
plugs and self tapers I’ll give the screws about three years and
they’ll need replacing.
I have to thanks Sue who took on the task of spraying the old frame
on which the Nova 3000 sits. Four cans of Fiddly Bits after a light sand
a few days drying time and the Nova is back up and running……..not
without drama must always remember the locating swivel pin must be lined
up with the locating lock bolt. Still tempted to re-spray the Nova a
good clean was all it got. It took the good part of a day to line up
level up the beds, some how I ended up with packing washers left over.
Prior the move one of the tool box trolleys had suffered a wonky
wheel Ken raced off to buy a new replacement unfortunate as it was it
was almost 1/4″ higher then the rest. The floor pan had always caused
problems with wheels almost collapsing due to poor reinforcement of the
floor pan area. I bought the remaining three matching new wheels, two
strips of zinc plinth bar and removed the rather useless manufacturing
packing plates.
It wasn’t until final fitting the size difference was noticed last photo above the matching wheels fitted.
New tool trolley handles made and fitted. Why have the many producers
of tool boxes and trolleys stopped fitting sensible easy grab handles?
These useless finger grip edge handles even if I was not suffering
arthritis in a work environment would drive me round the twist. Oily,
greasy hands trying to fumble with no more than a finger tip to open
draws full of tools obviously the majority of users work in pristine
environments.
Sue had a bookcase which required a centre partition due to distance
between supports being to large. Yes i made it but I was following
directions of design originally. A woman is always allowed to change her
mind. Anyway we now share the bookcase, we need another.
I had to of course drill the holes required for shelf support pins.
Sue lacquered the new shelves and partition addition.
One side of the workshop is taking form and is quit workable, note
flooring has been laid again checker plate workshop vinyl. A new storage
shelf for the Myford frame and cover. old pantry now storage for
finishes and unfinished projects hanging space for squares and rulers.
Last photo above taken about 3.30pm as sun begins to set with that
I’ll leave this and go post another this time on Sue who has been
helping me do much of this above.
